Commarker Omni için Nihai Malzeme Ayarları Kılavuzu 1 UV Lazer Gravür Makinesi

Gevrek Olmak, Her substratta tutarlı sonuçlar, sağ lazer parametrelerini arayarak başlar. The ComMarker Omni 1—with its 5 W UV fiber laser—excels at high‑precision engraving and cutting across plastics, woods, metaller, bardak, taş, and even organic materials. Below is an in‑depth, step‑by‑step reference to help you master material settings in Hafif Yanık (or EZCad2) için 16 of the most common substrates.

---

📘 Why Proper Material Settings Matter

• Kesinlik & Zıtlık: UV lazerler interact differently with each material. Too much power can scorch, too little leaves faint marks.
• Hız & Throughput: Optimized speeds reduce cycle time without sacrificing quality.
• Longevity: Correct settings minimize wear on optics and prolong laser tube life.
• Emniyet: Proper passes and focus reduce fire risk and noxious fumes.

Before you begin, always:

1. Clean Your Work Area – Remove debris and secure your material flat.
2. Focus Carefully – Use the red‑dot preview and electric Z‑axis on the Omni 1 for pixel‑perfect focus.
3. Ventilate – Run an exhaust fan or air purifier, especially on plastics, deri, and organic substrates.

---

⚙️ Core Laser Parameters Explained

• Güç (%): Laser intensity (0–100%). Higher power means deeper cuts or darker marks.
• Hız (mm/sn): How fast the head moves. Faster speeds reduce burn but may lighten the mark.
• Sıklık (kHz): Pulse repetition rate. Higher frequency gives smoother edges on plastics and metals.
• Q‑Pulse Width: Pulse duration. Longer pulses (higher Q‑pulse) deposit more energy per pulse—useful for marking metal or leather.
• Geçişler: Number of times the laser follows the same path. Multiple shallow passes yield cleaner results on thick or reflective materials.
• Hat aralığı (mm): Spacing between raster lines. Smaller intervals increase resolution at the cost of time.
• Image Mode (LightBurn only): For grayscale or 2.5D effects (Örneğin., Atkinson dithering).

---

🛠️ 1. Clear Acrylic Engraving

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	1,000 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	1
Hat aralığı	0.03 mm

Tips:

• Mask the back with painter’s tape to catch smoke residue.
• Engrave on the underside for a frosted‑glass look.
• Test a small corner to fine‑tune power if your acrylic is thicker than 3 mm.

---

🍃 2. Leaf Pattern on Acrylic

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	500 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	1
Hat aralığı	0.03 mm
Image Mode	Atkinson

Tips:

• Kullanmak Atkinson dithering for smooth gradients on grayscale leaf images.
• Keep intervals tight (0.03 mm) to preserve delicate veins and edges.
• Work on 5 mm acrylic for more dramatic depth.

---

🥂 3. Cam gravür

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	200 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	1
Hat aralığı	0.03 mm

Glass Ornaments: Same settings, but rotate your piece on a rotary attachment.
Tips:

• Apply a thin layer of dish soap or cover with a damp paper towel to reduce micro‑chipping.
• Engrave slowly (200 mm/s) to avoid cracking.
• Polish edges afterward with a soft cloth for clarity.

---

🥥 4. Coconut Shell Engraving

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	500 mm/s
Sıklık	30 kHz
Q‑Pulse Width	1
Geçişler	1
Hat aralığı	0.03 mm

Tips:

• Sand the surface lightly before engraving to remove fibrous residue.
• Coconut shells vary—test a scrap piece for ideal power.
• Use a dust mask when cleaning up coconut dust.

---

🎖️ 5. Leather Badge Engraving & Kesme

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Marking Pass

Parametre	Değer
Güç	30 %
Hız	1,000 mm/s
Sıklık	30 kHz
Q‑Pulse Width	20
Geçişler	1
Hat aralığı	0.03 mm

Cutting Pass

Parametre	Değer
Güç	40 %
Hız	100 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	5
Hat aralığı	0.03 mm

Tips:

• Kullanmak vegetable‑tanned leather for best contrast and minimal fumes.
• Mark first, then cut—this prevents scorch marks on the edges.
• Adjust Q‑pulse width higher (20) daha derin için, darker marks on grainy hides.

---

📦 6. 4 mm MDF Cutting

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	40 %
Hız	75 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	10

Tips:

• MDF can char—use light passes (10 passes at 75 mm/s) to cut through without heavy burning.
• Vacuum dust between every 2–3 passes to improve cut quality.
• Seal edges with clear lacquer to prevent moisture uptake.

---

🌲 7. Odun gravürü & Kesme

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Oymak (115×115 mm lens)

Parametre	Değer
Güç	30 %
Hız	200 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	3
Hat aralığı	0.03 mm
Extras	Cross‑hatch & flood fill enabled

Kesme (115×115 mm lens)

Parametre	Değer
Güç	30 %
Hız	50 mm/s
Sıklık	30 kHz
Q‑Pulse Width	1
Geçişler	6

Tips:

• Kullanmak birch plywood veya basswood for consistent results.
• Cross‑hatch fill gives a textured look—great for signage.
• Slow (50 mm/s) and multiple passes (6) for clean cuts through 3–5 mm wood.

---

🌾 8. Rice Grain Laser Engraver

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	100 mm/s
Sıklık	40 kHz
Q‑Pulse Width	15
Geçişler	1

Tips:

• Place grains on double‑sticky tape to hold them steady.
• Low speed and higher Q‑pulse width (15) ensure legible micro‑marks.
• Perfect for novelty jewelry or micro‑engraving demos.

---

🎧 9. Plastic Earphone Case Engraving

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	1,000 mm/s
Sıklık	40 kHz
Q‑Pulse Width	15
Geçişler	1
Hat aralığı	0.03 mm

Tips:

• Mask with low‑tack tape to reduce melt lines.
• High speed (1,000 mm/s) prevents warping of thin plastics.
• Q‑pulse width 15 gives deeper contrast on matte finishes.

---

🍾 10. Wine Bottle Rotary Engraving

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	600 mm/s
Sıklık	40 kHz
Q‑Pulse Width	5
Geçişler	2
Rotary Split	0.1 mm
Rotary Overlap	0.1 mm

Tips:

• Secure bottle in the rotary attachment.
• Slow, multi‑pass engraving ensures even coverage.
• Use a clear lacquer after engraving to protect the finish.

---

🧴 11. Havlu (Textile) Oymak

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	2,500 mm/s
Sıklık	30 kHz
Q‑Pulse Width	17
Geçişler	1

Tips:

• Kullanmak 100% cotton towels for crisp marks.
• High speed (2,500 mm/s) prevents fabric burning.
• A single pass at Q‑pulse 17 provides a subtle, permanent mark.

---

📄 12. Paper Laser Cutting

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	100 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	3–5
Hat aralığı	0.03 mm

Tips:

• Use heavier cardstock (200–300 gsm) for crisp cuts.
• Multiple passes (3–5) at low speed ensure clean edges.
• Mask both sides with low‑tack tape to prevent burn‑through.

---

🧲 13. Metal Bottle Opener Engraving

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	833.3 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	1
Hat aralığı	0.03 mm

Tips:

• Clean metal with isopropyl alcohol before engraving.
• Single pass at high speed for subtle, durable marks.
• Follow with a clear coat to protect against wear.

---

👟 14. PU Shoes (Sentetik deri)

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	1,000 mm/s
Sıklık	30 kHz
Q‑Pulse Width	20
Geçişler	1
Hat aralığı	0.03 mm

Tips:

• PU leather engraves similarly to genuine leather but with less depth.
• Higher Q‑pulse width (20) ensures crisp contrast.
• Test a hidden seam first to confirm settings.

---

🪨 15. Slate Engraving

Makine: Omni 1 (UV 5 W)
Yazılım: Hafif Yanık

Parametre	Değer
Güç	30 %
Hız	1,000 mm/s
Sıklık	40 kHz
Q‑Pulse Width	1
Geçişler	1

Tips:

• Slate’s natural texture creates a handsome, weathered look.
• Single high‑speed pass leaves a clear white mark.
• Seal slate afterward with a matte stone sealant.

---

🔄 Wrapping Up

With these detailed settings, you’re ready to tackle virtually any engraving or cutting project on your ComMarker Omni 1 UV Laser Engraver. Hatırlamak:

1. Always test on scrap material first.
2. Adjust power/speed in small increments.
3. Maintain your machine—clean optics and verify focus regularly.

Have questions or need further assistance? The ComMarker support team is here 24/7 to help you optimize settings and troubleshoot any challenge. Now fire up LightBurn, load your favorite design, and let the Omni 1 bring your ideas to life!